2013-11-08

Reducing Quantization Noise with BitScope

Digital Oscilloscope Waveform Quantization Example

100mV sinusoid waveform at different ranges (hit ESC key to stop)

As with any digital oscilloscope, quantization noise is produced when converting analog signals to their digital form.

However, unlike some low cost scopes this is usually not a problem with BitScope because the noise can be minimized using its software controlled analog attenuators and prescalers.

This ensures A/D convertion is optimized.

The remaining quantization noise is very low when compared to the digitized signal and cannot be seen on the display. This animation shows a 100mV sine wave at some varying attenuation and prescale values on BS325.

It's the same signal in each case but the resolution of the waveform shown changes dramatically as the ranges are changed. The smoothest waveform is the one captured with optimum attenuation and prescale. However, when measuring very low level signals or when performing spectrum analysis (as can be done with BitScope), minimizing quantization noise further can be beneficial.

BitScope Resolution Enhancement Features

Most digital oscilloscopes start to have problems working with signal below about 10mV but BitScope offers a range of options to improve capture resolution and reduce quantization noise for work at any signal level:

FunctionDescription
Analog AttenuatorsBitScope's analog front end electronics offer a range of software selectable attenuation and gain stages to scale the signal to optimum levels prior to the A/D convertor. It's important to note that unlike some devices which offer switchable attenuation only, BitScope offers gain stages as well. This is very important because it can improve immunity from external noise sources in all ranges.
Analog PrescalersSome models like BS445 and BS325 also offer software selectable analog prescalers which increase the gain available for work with lower signal levels without reducing the A/D capture resolution. Prescalers can also be used to compensate for higher levels of probe attenuation, for example when measuring high impedance signal sources.
Resolution EnhancementAll BitScopes have large capture buffers compared to the 1k sample buffer typically found in other digital scopes. From BS10 with 12k buffers to BS325 with up to 512k, these large buffers allow BitScope to improve sample resolution after the signal has been captured, from its native (8 bits) up to 12 bits or more in some cases.
A/D Macro ModeFor lower bandwidth work some models like BS10 offer Macro Mode which applies a bandlimiting filter and uses a 12 bit A/D convertor instead of its wide band 8 bit one.
Switchable FiltersSome noise sources that can affect capture resolution are at different (higher) frequencies than the signal of interest. In these cases a switchable RF filter is available in some models to remove this interference prior to conversion.
Input OffsetsMany digital oscilloscopes have problems when looking at small signals sitting on a large DC bias or on a large but much lower frequency bias signal. AC coupling can help for a DC bias but dynamically controlled analog front end input offsets are really required to shift the small signal of interest to zero to maximize capture resolution.
Oscilloscope ProbesAll BitScopes that have BNC inputs are compatible with a wide range of standard oscilloscope probes. These offer attenuation ranges for work with higher level signals and are designed to maximize noise rejection.

Most of these features are activated automatically when using BitScope software such as BitScope DSO or Meter. Others may be applied manually or with custom software written with the BitScope Library. When combined they allow BitScope to be used for high resolution analog waveform capture, analysis and data acquisition. We'll write more about how to minimize noise and maximize waveform resolution in future posts. Stay tuned!

Related Posts

BitScope
Build a powerful mixed signal workstation with one simple 3D print !Sep 3
Raspberry
Raspberry Pi 3 Launch and BitScope BladeFeb 29
BitScope
Physical Computing with Raspberry Pi and BitScope!Dec 01
Raspberry
BitScope Blade for Raspberry Pi at Hannover Maker Faire!Jun 05
Software
BitScope DSO 2.9 Now Available.Jun 02
BitScope
Getting Started with BitScopeMay 08
Education
BitScope Micro & Raspberry Pi in Education at BETTJan 21
Education
Electronic Measurement with BitScope & Raspberry PiNov 12
BitScope
Hands on with BitScope Micro at electronica 2014Nov 11
BitScope
BitScope Micro Video Tutorial with Farnell element14Nov 10
BitScope
BitScope Micro and Raspberry Pi at electronica 2014!Nov 06
BitScope
BitScope Micro element14 Webinar Review.Nov 03
BitScope
BitScope Micro Webinar with element14!Oct 29
BitScope
element14 launches BitScope Micro for Raspberry Pi!Oct 27
BitScope
BitScope Micro Diagnostic Port Explained.Aug 16
Software
BitScope Touch Screen User InterfaceOct 28
Software
Vertical Offsets and Dual Channel DisplayOct 19
BitScope
Dual Channel Active Differential Probe (New Product).Oct 15
BitScope
BitScope Smart Port. The clever connection.Oct 12
Raspberry
Visualizing sound with Sonic Pi and BitScopeOct 05
BitScope
Differential measurements matter, here's why...Oct 01
Raspberry
BitScope Raspberry Pi OscilloscopeSep 25
More...